| | | |
Supported XCM Retailers: Extreme-Mods.com - Located in the USA & Recommended
|
#1
01-24-2009, 12:31 AM
| |||
| |||
 rapid gear light
installed fairly easy..... problems.... left bumper doesnt work. right trigger bairly works and sticks when it does and doesnt rapid fire.... right bumber shows lights on and rapid blinking but i cant use it either way in the game i am trying it on... right bumber is my reload but doesnt reload.... etc... any suggestions? plz im in reall need... this is my only controller at the moment... i cant wait to get this working fully.  also.... how much of a cut for the traces... maybe mine are too deep? or does that matter for those will a simple small slice across it be enough to sever connection? Last edited by dvannunn; 01-24-2009 at 12:48 AM.      |
|
#2
01-24-2009, 01:32 AM
| ||||
| ||||
You'll need to double check with a microscope, then you'll be able to tell if they are cut fully or not. You should get another controller to use as backup, it wasn't a very good idea to mod your only controller.
__________________ Extreme-Mods.com - Based in the USA - Best Price Guarantee! Search Engine Optimization & Web Solutions |
|
#3
01-24-2009, 01:33 AM
| ||||
| ||||
|
Rule #1: Always have a backup, you never know what will happen when fooling with the insides of a controller.
__________________ Extreme-Mods.com - Based in the USA - Best Price Guarantee! Search Engine Optimization & Web Solutions |
|
#4
01-24-2009, 02:59 AM
| ||||
| ||||
|
you sound like you had the problem I was having but the bumper problem. make sure you have the (this) IF you have that orange Pcb v2 and 360T. the trigger will not work right. if you have the 360T2 and a different orange pcb v2, you'll have the right trigger problem like your talking about.
|
|
#5
01-24-2009, 03:20 AM
| |||
| |||
|
i was using the old pcb for old model controller. i just went to walmart and got 2 more controllers.... i hope there the new ones so i dont have to undo the old board.... this time i will post pics before durin and after...... also i got that microscope from radioshack and i dont see how u used it. well not with the old model... could get it focused on some parts because it wouldnt go flush with it..... i will start in a few min after i eat.  |
|
#6
01-24-2009, 03:39 AM
| ||||
| ||||
| Quote:
|
|
#8
01-24-2009, 10:00 PM
| |||
| |||
|
well im done! all buttons work.. i think the game im tryin to use it for doesnt do the right trigger fast shooting like i want... tryin to get it to work for gears2 like i can pull trigger faster than it can but maybe its better in another game....... hmmm also LTO was a pain in the ***......... i unsoldered the little thingy off the board lol then said screw it and layed it back on and soldered it and the wire to the board..... ehhh but it works lol  By dvannunn, shot with Canon EOS 400D DIGITAL at 2009-01-24  By dvannunn, shot with Canon EOS 400D DIGITAL at 2009-01-24  By dvannunn, shot with Canon EOS 400D DIGITAL at 2009-01-24  By dvannunn, shot with Canon EOS 400D DIGITAL at 2009-01-24  By dvannunn, shot with Canon EOS 400D DIGITAL at 2009-01-24 |
|
#9
01-24-2009, 10:00 PM
| |||
| |||
 By dvannunn, shot with Canon EOS 400D DIGITAL at 2009-01-24 ^ i soldered the grnd and stuff after this photo  By dvannunn, shot with Canon EOS 400D DIGITAL at 2009-01-24 |
|
#10
01-24-2009, 10:24 PM
| ||||
| ||||
|
nice job. that PCB works with the 360t2 but it has some problems with the right trigger sometimes. for games like gears and COD World at War. The button had to be adjusted to a certain speed. If you wish to learn how to added a button to do that feel free to pm me.
|
Linear Mode
